How to Fix iPhone 6 Camera Not Working Issue

The camera does not work, this is really a troublesome issue, if you want to get rid of this failure as soon as possible, reading this article, you will know the best way to solve iPhone 6 Camera Not Working. When you turn on camera on iPhone 6 to take photos, you found the iPhone rear camera not working, it can't take pictures. 


The J2321 is the interface of rear camera. After checking the iPhone 6 schematic diagram on WUXINJI Dongle, we know that there are 4 sets of power supply circuit; they go through inductance L2329, L2330, L2318, FL2343 to the rear camera interface J2321, where the PP2V85_RCAM_AVDD_CONN is 2.8V power supply! It is provided by the small glass ID-- U2301, when turn on the iPhone camera, the CAM_EXT_LDO_EN signal that sent from the iPhone CPU controls 2.8V voltage that output by U2301, and then after the inductor FL2343, send to the interface J2321. 

No matter U2301 fell into water or ground, it is easy to damage, and then causes no 2.8V voltage; the final result is that the iPhone can't take pictures. For the damaged power supply tube, we can remove it directly. And the for the water damaged iPhone, the L2329, L2330, L2318, FL2343 is easy to corrode and cause not to take pictures, you can short connect it with QUICK 861DW hot air rework station and jump wire. 

Also, the iPhone flash IC--U1602 has several data signal is share with camera (AP_TO_RCAM_I2C_SCL, AP_BI_RCAM_I2C_SDA), so, the short circuit iPhone flash IC -- U1602 also can cause iPhone won't take pictures. 



The repair process for the iPhone camera can't take pictures is as follows:

1.check the socket for corrosion, if yes, clean it and weld it

2.check if inductance L2329, L2330, L2318 and FL2343 are open circuit, if yes, short connect it.

3.check if C2303 has 2.8V when open the iPhone camera, if not, replace the new U2301, or you can remove it and short connect it.

4.check if C2323 has 1.8V, C2389 has 1.2V, C2390 has 1.8V, if both of them is normal, and interface also weld well, then try to replace iPhone camera flash control IC（VC541） U1602. Moreover, this IC output the flash light control signal PP_STRB_DRIVER_TO_LED_COOL, PP?_STRB_DRIVER_TO_LED_WARM, after iPhone boot flex cable interface to flash IC LED. If the flash light not working properly, first you should check LED. 

5.Use Fluke 15B+ Digital Multimeter to measure the voltage of PP_VCC_MAIN on capacitor C1686 to check if it is normal, and check if L1605 is open circuit. If both of them is normal, but the fault is still exists, then you need to replace the U1602 flash IC.

Tips: Need any professional cell phone repair skills or phone repair  tools, please contact VIP Pro Shop Team for help!

Comments

Post a Comment

Popular posts from this blog

My iPhone Got Wet! How To Fix iPhone Water Damage?

Image
 Water damage tends to worsen with time, and it is among the more challenging DIY repairs to undertake, so this guide covers the basic iPhone repair of water damage.  1. Remove iPhone from the water and Turn it off Remove your iPhone from the water as soon as safely possible. Minimize the length of time the iPhone and water are in contact to minimize corrosion. If your phone is still on when removed from the water, attempt to turn it off. If it's off, do not attempt to turn it on. 2. Check External Ports Check any external ports (charging port, headphone jack, SIM card slot, etc.) for corrosion as well. These may have to be cleaned out with alcohol and a  Anti Static Brush , or replaced if cleaning is not practical. Pay special attention to cable ends, battery contacts, connectors, pins, and fuses, as these parts are prone to corrosion and can easily cause the phone to malfunction. Test all the buttons and features (such as the microphone, s
Read more

2021 Latest MagicAWRT Adapter Restore Tool for Apple Watch

Image
 Here we have the latest MagicAWRT adapter Apple Watch restore tool in 2021, and MagicAWRT offers its complete solutions to fix many apple watch problems. MagicAWRT Adapter is intended for solving service problems with Apple Watch S0/SE/S1/S2/S3/S4/S5/S6 (38 mm / 42 mm / 40 mm / 44 mm). It can solve problems such as white apples, exclamation points, restarts, stuck on screens, poor touch, ID lock, etc. It also can fix related issues that are caused by  Apple Watch glass digitizer touch replacement. Apple Watch Firmware for MagicAWRT Adapter Restore Tool will not be provided, and the customer needs to download themselves. 1. Using MagicAWRT Adapter to reset Apple Watch Data with or without Backup MagicAWRT Recovery Adapter Restore Tool is the best iOS data restore software in the market because of its ease of use and attractive user interface. Most Apple Watch users data losses are due to accidents, failed jailbreaks, hardware and software failures, factory resets, and theft. It would
Read more

How To Solve iPhone X Voltage Jumping Issue

Image
Today, We getting the iPhone X main board to test, we observe the current value repeatedly jumps between 0mA and 50mA on DC power supply , and it is different from the normal booting current. Next, test whether the power supply of every circuit is normal. PP_VDD_MAIN is measured 4.2V; PP_VDD_BOOST measured is 4.2V. PP1V8-ALWAYS is 1.8V, all the values are normal. But when testing PP1V1_S2, PP0V8_SOC_FIXED_S1, PP1V8_S2 and other circuit voltage that output by power chip U2700 voltage are jumping constantly. According to previous experience, voltage jump is usually caused by a power supply circuit of U2700 output. Measured with digital multimeter , there is no short circuit was found for the dipole value of all power supply to ground. We repaired iPhone 7P before and know that if crystal oscillator is false welding can also cause voltage jumping, And if iPhone CPU power supply is abnormal also can cause voltage jumping. Check the crystal oscillator we find no problem, then check th
Read more