GUIDE: How to replace damaged iphone 7/ 7 Plus screens by yourself

Now many people are using Apple phone, after using a period of time, can not avoid some small problems, The iPhone 7 Plus's screen is vulnerable, such as dropped, smashed, or otherwise chipped against surfaces, so much as you completely smash your screen, you're probably in need of a screen repair. When you crack your screen, maybe you will encounter some difficulties about detail, such as it also destroys your iPhone's water resistance. If your iPhone 7 Plus screen is broken, you want to replace the screen by yourself. vipprogrammer will help you. 



Trouble Phenomenon:

iphone 7/ 7Plus Screen damaged,  The iphone screen dropped on the ground broken, you want to replace the screen by yourself, how to fix it at home? 

Repair Process: 

1. Put off the iPhone 7 Plus.

2. Using a TS1 (0.8mm) screwdriver kit tools to remove the two screws, at the bottom of the phone locate.

3. Above the Home button, put a suction cup directly on the display and gently try to remove from the rear casing.

4. If necessary, use a wedging device to carefully break the seal of the adhesive and pry the display from the rear casing.

5. Open the iPhone 7 display and remove the four screws to free the display plate. Then use tweezers to lift the display plate away.

6. Use the spudger tool to pull of the three LCD connecting cable strips.

7. Unscrew two more tri-point screws at the top, right-hand corner that hold down your proximity sensor.

8. Remove the plate over the proximity sensor reveal one more cable strip that, when disconnected, will free the front display from the back of the phone.



9. Remove the three Phillips-head screws from the bracket behind the ear speaker at the top of the display side.

10. Pulling away The bracket to reveal the iPhone’s camera.

11. Pull back the camera to remove the two screws holding in the ear speaker assembly, and lift out the ear speaker.

12. Gently wiggle and pull up on the proximity sensor to remove it. Find the touch ID assembly, at the bottom of the display side.

13. Unscrew the four tri-point screws holding down the bracket, and remove bracket.

14. Gently wiggle to remove touch ID, then remove the LCD back-plate by unscrewing six, tri-point screws.





15. Using the spudger tool, lift up the LCD back-plate to reveal the cable strip connected to back-plate.

16. When you free the LCD back-plate of the cable, it will disconnect easily.

17. Discard your old, damaged LCD and replace with the new screen, folding down your cables and lining up the side mounts, to put the 6 screws back into place.

18. Continue to follow the steps in reverse to reassemble the phone.

Tips: More information about phone repair guide and tools, you can choose Vip Pro Shop Team.





Comments

Post a Comment

Popular posts from this blog

My iPhone Got Wet! How To Fix iPhone Water Damage?

Image
 Water damage tends to worsen with time, and it is among the more challenging DIY repairs to undertake, so this guide covers the basic iPhone repair of water damage.  1. Remove iPhone from the water and Turn it off Remove your iPhone from the water as soon as safely possible. Minimize the length of time the iPhone and water are in contact to minimize corrosion. If your phone is still on when removed from the water, attempt to turn it off. If it's off, do not attempt to turn it on. 2. Check External Ports Check any external ports (charging port, headphone jack, SIM card slot, etc.) for corrosion as well. These may have to be cleaned out with alcohol and a  Anti Static Brush , or replaced if cleaning is not practical. Pay special attention to cable ends, battery contacts, connectors, pins, and fuses, as these parts are prone to corrosion and can easily cause the phone to malfunction. Test all the buttons and features (such as the microphone, s
Read more

2021 Latest MagicAWRT Adapter Restore Tool for Apple Watch

Image
 Here we have the latest MagicAWRT adapter Apple Watch restore tool in 2021, and MagicAWRT offers its complete solutions to fix many apple watch problems. MagicAWRT Adapter is intended for solving service problems with Apple Watch S0/SE/S1/S2/S3/S4/S5/S6 (38 mm / 42 mm / 40 mm / 44 mm). It can solve problems such as white apples, exclamation points, restarts, stuck on screens, poor touch, ID lock, etc. It also can fix related issues that are caused by  Apple Watch glass digitizer touch replacement. Apple Watch Firmware for MagicAWRT Adapter Restore Tool will not be provided, and the customer needs to download themselves. 1. Using MagicAWRT Adapter to reset Apple Watch Data with or without Backup MagicAWRT Recovery Adapter Restore Tool is the best iOS data restore software in the market because of its ease of use and attractive user interface. Most Apple Watch users data losses are due to accidents, failed jailbreaks, hardware and software failures, factory resets, and theft. It would
Read more

How To Solve iPhone X Voltage Jumping Issue

Image
Today, We getting the iPhone X main board to test, we observe the current value repeatedly jumps between 0mA and 50mA on DC power supply , and it is different from the normal booting current. Next, test whether the power supply of every circuit is normal. PP_VDD_MAIN is measured 4.2V; PP_VDD_BOOST measured is 4.2V. PP1V8-ALWAYS is 1.8V, all the values are normal. But when testing PP1V1_S2, PP0V8_SOC_FIXED_S1, PP1V8_S2 and other circuit voltage that output by power chip U2700 voltage are jumping constantly. According to previous experience, voltage jump is usually caused by a power supply circuit of U2700 output. Measured with digital multimeter , there is no short circuit was found for the dipole value of all power supply to ground. We repaired iPhone 7P before and know that if crystal oscillator is false welding can also cause voltage jumping, And if iPhone CPU power supply is abnormal also can cause voltage jumping. Check the crystal oscillator we find no problem, then check th
Read more