How To Fix iPhone 6 shows white Apple logo & reboot repeatedly - ViP Pro Shop Team

If you iPhone 6 shows white Apple logo then reboot repeatedly, Don't worry, This problem is common and can happen to any iPhone at any time for a variety of reasons, including upgrading to iOS 11. In this article, ViP Pro Shop Team are going to address this problem, showing you a few ways to fix it. 



The following are just some of the most common reasons:

When we press power button, the iPhone 6 shows Apple logo, and then auto reboot. This situation has been circulating, what's going on? 

Disassemble the iPhone 6, then measure the logic eeprom IC diode data with multimeter, the results were 443 and 657,the diode data of AP_BI_EEPROM_I2C_SDA is too large, this case could be caused by iPhone 6 was dropped, the solder pad was disconnected.

picture 7-5-1

picture 7-5-2

Today, Vipprogrammer will introduce a new method to solve this issue, solder jump wire without remove CPU, and just directly scrape the CPU and the solder jump wire.

Observe the logic board under the microscope, as shown in picture 7-5-3.

7-5-3

Then start scraping from the upper CPU, according the size of logic board and scrap it. As shown in picture 7-5-4, 7-5-5, 7-5-6.

7-5-4

7-5-5

7-5-6

Find the corresponding point on the logic board, soldering jump wire and paint green UV Fluxes Oil on it. As shown in picture 7-7-7.

7-7-7

Please note it, when scraping the middle CPU, be sure to be more careful. If you scrape off the other lines, the consequences are serious.

After finish the jumper wire, assemble the iPhone, then power on and test it, it can boot properly and go into the IOS. The problem has been solved, the maintenance is over. As shown in picture 7-7-8.

7-7-8

Tips: These tools are the most practical and safe, you can order automatic at www.vipprogrammer.com. Hoping you can benefit form it, all of these phone repair tools, and you can find it.


Comments

Post a Comment

Popular posts from this blog

2021 Latest MagicAWRT Adapter Restore Tool for Apple Watch

Image
 Here we have the latest MagicAWRT adapter Apple Watch restore tool in 2021, and MagicAWRT offers its complete solutions to fix many apple watch problems. MagicAWRT Adapter is intended for solving service problems with Apple Watch S0/SE/S1/S2/S3/S4/S5/S6 (38 mm / 42 mm / 40 mm / 44 mm). It can solve problems such as white apples, exclamation points, restarts, stuck on screens, poor touch, ID lock, etc. It also can fix related issues that are caused by  Apple Watch glass digitizer touch replacement. Apple Watch Firmware for MagicAWRT Adapter Restore Tool will not be provided, and the customer needs to download themselves. 1. Using MagicAWRT Adapter to reset Apple Watch Data with or without Backup MagicAWRT Recovery Adapter Restore Tool is the best iOS data restore software in the market because of its ease of use and attractive user interface. Most Apple Watch users data losses are due to accidents, failed jailbreaks, hardware and software failures, factory resets, and theft. It would
Read more

My iPhone Got Wet! How To Fix iPhone Water Damage?

Image
 Water damage tends to worsen with time, and it is among the more challenging DIY repairs to undertake, so this guide covers the basic iPhone repair of water damage.  1. Remove iPhone from the water and Turn it off Remove your iPhone from the water as soon as safely possible. Minimize the length of time the iPhone and water are in contact to minimize corrosion. If your phone is still on when removed from the water, attempt to turn it off. If it's off, do not attempt to turn it on. 2. Check External Ports Check any external ports (charging port, headphone jack, SIM card slot, etc.) for corrosion as well. These may have to be cleaned out with alcohol and a  Anti Static Brush , or replaced if cleaning is not practical. Pay special attention to cable ends, battery contacts, connectors, pins, and fuses, as these parts are prone to corrosion and can easily cause the phone to malfunction. Test all the buttons and features (such as the microphone, s
Read more

Free download: Ford / Mazda odometer correction tool software

Image
New Mazda OBD2 Tool is the Digital Odometers, Airbag reset and immobilizer programming cables by OBD2, it is a newly OBD2 device for Mazda Vehicle. Mazda OBD2 Tool is Mazda OBD2 Odometer correct and Airbag module repair tool, especially for Mazda vehicle from 2005-2015.It is OBD2 user friendly tool, used for calibrate odometer and airbag repair. For Mazda Digital Odometers programming and Airbag reseting Tool by OBD2 Mazda OBD Tool is used to calibrate the instrument for all CAN-bus Mazda cars from 2005 to 2015 including MADZA 3/ MADZA 6 / MADZA CX5 / MADZA CX7, as well as reset the airbag/SRS for Mazda with XC236X chip. 2017 New Ford / Mazda OBD2 Tool is the Car Digital Odometers and immobilizer programming cables, and Ford OBD2 Tool and Mazda OBD2 Tool is used to mainly perform Ford / Mazda Digital Odometers, instrument calibration and immobilizer key matching. Here, VIP Pro Shop Team will share the software download link for Ford OBD2 Tool and Mazda OBD2 Tool.
Read more