iPhone 6 Camera Not Working - What Should You Do?

When your iPhone 6 camera doesn't work, what do you do? today we'll share some tips to fix the problem for free. If you happen to read this article, then your cell phone will be saved.



Repair Process:

Step 1: Tap “Camera” icon and enter into camera mode, the rear camera can not be activated. Switch to front camera. It works normally.


Step 2: Let’s replace with a new rear camera at the beginning. Disassemble the phone, detach battery and then remove the display assembly. Take down the iphone6 rear camera and replace with a new rear camera.


Step 3: Get the display assembly buckled and connect the iphone 6 battery. Then power on and test. The rear camera still can not be activated.

Step 4: Remove the display assembly and take down the rear camera. Measure the rear camera power supply voltage. The power supply voltage value is normal.



Step 5: Then, measure the resistance between rear camera connector and grounding. Resistance value of pin 30 is 303, which is abnormal. The reference resistance value of pin 30 should be 537 or so.

Step 6: Pin 30 works as the activating signal of flashlight. It is also connected with pin E3 of flashlight IC U1602 via FL2322 and C2300.



Step 7: Take down the logic board. Then attach the logic board to PCB Holder. Then take down capacitor C2300 with Hot Air Gun at 320℃. Then measure the resistance between pin 30 and grounding again. Resistance value of pin 30 is 300, which is abnormal.

Step 8: Then we can draw the conclusion that IC U1602 broke down.

Step 9: Take off the shield plate of CPU with Hot Air Gun at 320℃. We can see that the flashlight IC is right next to CPU, and to protect the CPU from high temperature when removing IC, we need to cover the CPU with the detached shield plate.

Step 10: Blow with Hot Air Gun at 320℃ and pry off the flashlight IC with sculpture knife. After that, clean tins on the bonding pad with Soldering Iron. Then clean again with PCB Cleaner.

Step 11: Once the logic board is cooling enough, measure the resistance between pin 30 and grounding again. Resistance value of pin 30 is 0, which is normal.

Step 12: Apply some BGA Paste Flux to the bonding pad and align the new flashlight IC to the right place. Remember to cover the CPU with the detached shield plate. Then solder the new flashlight IC with Hot Air Gun at 320℃.

Step 13: Once soldering is finished, wait for the iphone logic board to cool for 5 minutes. Then measure the resistance between pin 30 and grounding again. Resistance value of pin 30 is 518, which is normal. Which also indicates that the fault has been cleared.


Step 14: Get the logic board assembled and connect the battery. Buckle the display assembly and power on. The rear camera can be activated this time. Rear camera fault repair finished.

Related videos: https://www.youtube.com/watch?v=A4UwhwtpQ1g


Tips: If you need more information and professional repair skilled, you want to consult, please check here. We'll give you a free answer. 

Comments

Post a Comment

Popular posts from this blog

My iPhone Got Wet! How To Fix iPhone Water Damage?

Image
 Water damage tends to worsen with time, and it is among the more challenging DIY repairs to undertake, so this guide covers the basic iPhone repair of water damage.  1. Remove iPhone from the water and Turn it off Remove your iPhone from the water as soon as safely possible. Minimize the length of time the iPhone and water are in contact to minimize corrosion. If your phone is still on when removed from the water, attempt to turn it off. If it's off, do not attempt to turn it on. 2. Check External Ports Check any external ports (charging port, headphone jack, SIM card slot, etc.) for corrosion as well. These may have to be cleaned out with alcohol and a  Anti Static Brush , or replaced if cleaning is not practical. Pay special attention to cable ends, battery contacts, connectors, pins, and fuses, as these parts are prone to corrosion and can easily cause the phone to malfunction. Test all the buttons and features (such as the microphone, s
Read more

2021 Latest MagicAWRT Adapter Restore Tool for Apple Watch

Image
 Here we have the latest MagicAWRT adapter Apple Watch restore tool in 2021, and MagicAWRT offers its complete solutions to fix many apple watch problems. MagicAWRT Adapter is intended for solving service problems with Apple Watch S0/SE/S1/S2/S3/S4/S5/S6 (38 mm / 42 mm / 40 mm / 44 mm). It can solve problems such as white apples, exclamation points, restarts, stuck on screens, poor touch, ID lock, etc. It also can fix related issues that are caused by  Apple Watch glass digitizer touch replacement. Apple Watch Firmware for MagicAWRT Adapter Restore Tool will not be provided, and the customer needs to download themselves. 1. Using MagicAWRT Adapter to reset Apple Watch Data with or without Backup MagicAWRT Recovery Adapter Restore Tool is the best iOS data restore software in the market because of its ease of use and attractive user interface. Most Apple Watch users data losses are due to accidents, failed jailbreaks, hardware and software failures, factory resets, and theft. It would
Read more

How To Solve iPhone X Voltage Jumping Issue

Image
Today, We getting the iPhone X main board to test, we observe the current value repeatedly jumps between 0mA and 50mA on DC power supply , and it is different from the normal booting current. Next, test whether the power supply of every circuit is normal. PP_VDD_MAIN is measured 4.2V; PP_VDD_BOOST measured is 4.2V. PP1V8-ALWAYS is 1.8V, all the values are normal. But when testing PP1V1_S2, PP0V8_SOC_FIXED_S1, PP1V8_S2 and other circuit voltage that output by power chip U2700 voltage are jumping constantly. According to previous experience, voltage jump is usually caused by a power supply circuit of U2700 output. Measured with digital multimeter , there is no short circuit was found for the dipole value of all power supply to ground. We repaired iPhone 7P before and know that if crystal oscillator is false welding can also cause voltage jumping, And if iPhone CPU power supply is abnormal also can cause voltage jumping. Check the crystal oscillator we find no problem, then check th
Read more