iPhone 6 Plus no service after dropped - Look Here!

We all knowledge, when your iPhone was dropped before. And then the iPhone shows no service. You will be very anxious and angry,Following this article, The VIP Pro Shop Team will help you solve this problem.



According our experience, we suspect that the no service fault is caused by RF circuit. Now let's verify it.

Firstly, disassemble the iPhone by JM-P01 Essential Toolkit, and then carefully remove the iPhone motherboard. Observe the iPhone motherboard appearance, no obvious scars.

Secondly, use multimeter to measure the several main test points, we found that the diode data of testing point PP3170_RF is larger than the normal one 0.406.

Thirdly, plug the WUXINJI Dongle to computer and then open it to check the iPhone circuit diagram, we found that the test point PP3170_RF is the clock signal RFFE1_CLK of RFFE bus input by baseband CPU. Checking the PCB bitmap, we can see RFFE1_CLK’s signal is sent to many chips.



Fourth, with the help of hot air gun and Precision Titanium Alloy Tweezers, we remove these chips smoothly and quickly, we found many solder pads of these chips have dropped off from motherboard. Then we weld the jump wire to connect these pins of dropped solder pads, and then paint green oil and reweld those chips.

Fifth, measure the diode data of testing point PP3170_RF again, now the data is normal. Install the iPhone and turn on it to test, after enter the IOS, we type *#06# on the keypad, the the IMEI can be displayed on the iPhone touch screen.

Finally, insert the SIM card, the iPhone has signal and network, and the phone can be dialed normally.


Note: There are several reasons for no service: no baseband (no IMEI and modem firmware), iPhone does not read the SIM card (no ICCID), RF circuit damaged. If dropped iPhones displays no service, components pseudo soldering or open circuit may cause the problem.

Tips: If you need more information and professional repair skilled, you want to consult, please check here. We'll give you a free answer.

Comments

Post a Comment

Popular posts from this blog

My iPhone Got Wet! How To Fix iPhone Water Damage?

Image
 Water damage tends to worsen with time, and it is among the more challenging DIY repairs to undertake, so this guide covers the basic iPhone repair of water damage.  1. Remove iPhone from the water and Turn it off Remove your iPhone from the water as soon as safely possible. Minimize the length of time the iPhone and water are in contact to minimize corrosion. If your phone is still on when removed from the water, attempt to turn it off. If it's off, do not attempt to turn it on. 2. Check External Ports Check any external ports (charging port, headphone jack, SIM card slot, etc.) for corrosion as well. These may have to be cleaned out with alcohol and a  Anti Static Brush , or replaced if cleaning is not practical. Pay special attention to cable ends, battery contacts, connectors, pins, and fuses, as these parts are prone to corrosion and can easily cause the phone to malfunction. Test all the buttons and features (such as the microphone, s
Read more

2021 Latest MagicAWRT Adapter Restore Tool for Apple Watch

Image
 Here we have the latest MagicAWRT adapter Apple Watch restore tool in 2021, and MagicAWRT offers its complete solutions to fix many apple watch problems. MagicAWRT Adapter is intended for solving service problems with Apple Watch S0/SE/S1/S2/S3/S4/S5/S6 (38 mm / 42 mm / 40 mm / 44 mm). It can solve problems such as white apples, exclamation points, restarts, stuck on screens, poor touch, ID lock, etc. It also can fix related issues that are caused by  Apple Watch glass digitizer touch replacement. Apple Watch Firmware for MagicAWRT Adapter Restore Tool will not be provided, and the customer needs to download themselves. 1. Using MagicAWRT Adapter to reset Apple Watch Data with or without Backup MagicAWRT Recovery Adapter Restore Tool is the best iOS data restore software in the market because of its ease of use and attractive user interface. Most Apple Watch users data losses are due to accidents, failed jailbreaks, hardware and software failures, factory resets, and theft. It would
Read more

How To Solve iPhone X Voltage Jumping Issue

Image
Today, We getting the iPhone X main board to test, we observe the current value repeatedly jumps between 0mA and 50mA on DC power supply , and it is different from the normal booting current. Next, test whether the power supply of every circuit is normal. PP_VDD_MAIN is measured 4.2V; PP_VDD_BOOST measured is 4.2V. PP1V8-ALWAYS is 1.8V, all the values are normal. But when testing PP1V1_S2, PP0V8_SOC_FIXED_S1, PP1V8_S2 and other circuit voltage that output by power chip U2700 voltage are jumping constantly. According to previous experience, voltage jump is usually caused by a power supply circuit of U2700 output. Measured with digital multimeter , there is no short circuit was found for the dipole value of all power supply to ground. We repaired iPhone 7P before and know that if crystal oscillator is false welding can also cause voltage jumping, And if iPhone CPU power supply is abnormal also can cause voltage jumping. Check the crystal oscillator we find no problem, then check th
Read more