IPhone 7P Large Current Fault - How to Fix?

A user sent an iPhone 7P motherboard with high current fault.Today, we will show you How to fix this issue.




When receiving the motherboard, the first step is to have observation on it, it is slightly water damaged, large current when connecting on DC power supply, 3.8V short circuited. Because it is slightly water damaged, firstly check the specific damaged area, and find that the capacitance is corroded, which is the capacitance on the 3.8V circuit. 11-2-1



Pick up the fault and solve it, then clean it in the water inlet, gently fix the trouble and test the whole function after screen installation, now all other functions are normal, but there is no service on the iPhone 7 Plus.

Observe the radio frequency section under the Trinocular Stereo Microscope, we find the reception of the front end is corroded. 11-2-2


The fifth trace supply power for RF 1.8V, there is a serious corrosion and the layer is burned, scraping the bottom circuit to solder jumper wire. 11-2-3


It should be noted that this line is the same as a three branch road. If we want to connect the two sides to the bottom and scrape the bottom, if we are not familiar with the circuit, we suggest to scrape up the circuit and check it, then scrape the trouble layer, it's better to carefully do the operation with specialized cell phone repair knife so as to avoid unnecessary troubles. 11-2-4 


Last step, install screen to test, the fault is perfectly solved. The test of other functions are all normal now.


Tips: If you need more information and professional repair skilled, you want to consult, please check here. We'll give you a free answer. 

Comments

Post a Comment

Popular posts from this blog

My iPhone Got Wet! How To Fix iPhone Water Damage?

Image
 Water damage tends to worsen with time, and it is among the more challenging DIY repairs to undertake, so this guide covers the basic iPhone repair of water damage.  1. Remove iPhone from the water and Turn it off Remove your iPhone from the water as soon as safely possible. Minimize the length of time the iPhone and water are in contact to minimize corrosion. If your phone is still on when removed from the water, attempt to turn it off. If it's off, do not attempt to turn it on. 2. Check External Ports Check any external ports (charging port, headphone jack, SIM card slot, etc.) for corrosion as well. These may have to be cleaned out with alcohol and a  Anti Static Brush , or replaced if cleaning is not practical. Pay special attention to cable ends, battery contacts, connectors, pins, and fuses, as these parts are prone to corrosion and can easily cause the phone to malfunction. Test all the buttons and features (such as the microphone, s
Read more

2021 Latest MagicAWRT Adapter Restore Tool for Apple Watch

Image
 Here we have the latest MagicAWRT adapter Apple Watch restore tool in 2021, and MagicAWRT offers its complete solutions to fix many apple watch problems. MagicAWRT Adapter is intended for solving service problems with Apple Watch S0/SE/S1/S2/S3/S4/S5/S6 (38 mm / 42 mm / 40 mm / 44 mm). It can solve problems such as white apples, exclamation points, restarts, stuck on screens, poor touch, ID lock, etc. It also can fix related issues that are caused by  Apple Watch glass digitizer touch replacement. Apple Watch Firmware for MagicAWRT Adapter Restore Tool will not be provided, and the customer needs to download themselves. 1. Using MagicAWRT Adapter to reset Apple Watch Data with or without Backup MagicAWRT Recovery Adapter Restore Tool is the best iOS data restore software in the market because of its ease of use and attractive user interface. Most Apple Watch users data losses are due to accidents, failed jailbreaks, hardware and software failures, factory resets, and theft. It would
Read more

How To Solve iPhone X Voltage Jumping Issue

Image
Today, We getting the iPhone X main board to test, we observe the current value repeatedly jumps between 0mA and 50mA on DC power supply , and it is different from the normal booting current. Next, test whether the power supply of every circuit is normal. PP_VDD_MAIN is measured 4.2V; PP_VDD_BOOST measured is 4.2V. PP1V8-ALWAYS is 1.8V, all the values are normal. But when testing PP1V1_S2, PP0V8_SOC_FIXED_S1, PP1V8_S2 and other circuit voltage that output by power chip U2700 voltage are jumping constantly. According to previous experience, voltage jump is usually caused by a power supply circuit of U2700 output. Measured with digital multimeter , there is no short circuit was found for the dipole value of all power supply to ground. We repaired iPhone 7P before and know that if crystal oscillator is false welding can also cause voltage jumping, And if iPhone CPU power supply is abnormal also can cause voltage jumping. Check the crystal oscillator we find no problem, then check th
Read more