FIXD: iPhone 6 Plus Report Error 4014 After Nand Memory Expansion

Today, VIP Pro Shop Team will simplify the steps to tell you how to solve iPhone 6 Plus NAND memory extension to report error 4014, Follow this article and let us know the details and fix it.


Fault description:

The 6 iPhone Plus can be normally used before, there were no any problems. But after changing the iPhone Nand for memory capacity expansion, it reports error 4014 when flashing it. As shown in picture 10-3-1.




When we flash the iPhone device, it displays error 4014 before progress bar showing up. It is restored and the serial number could be recognized, which appeares after Nand expansion. This is usually caused by the iPhone USB chips leading to CPU problem. We get to know it UMT motherboard after disassembly, then remove USB chip U1700 to measure resistance from solder pad to CPU, we find that AP_TO_TRISTAR_ACC_UART6_TXD shows the infinite value, as shown in picture 10-3-2 and 10-3-3. 





 And AP_BI_12C0_SDA is also broken, as shown in picture 10-3-4 and 10-3-5.




The layer wire is disconnected, so we need to find out other connection point or digging for other holes, AP_TO_TRISTAR_ACC_UART6_TXD is direct connected without other external components, when digging the circuit AP_TO_TRISTAR_ACC_UART6_TXD we find that there is a hole next to socket, dig it to solder jumper wire. As shown in picture 10-3-6, 10-3-7 and 10-3-8.








AP_BI_12C0_SDA has a test point outside of the iPhone circuit board, welding directly from the test point. As shown in picture 10-3-9 and 10-3-10.





Intall the iPhone USB chip back, we can flash the iPhone device normally now, repair ends here!


Tips: If you need more professional repair skilled, you want to consult, please check here. We'll give you a free answer.

Comments

Post a Comment

Popular posts from this blog

My iPhone Got Wet! How To Fix iPhone Water Damage?

Image
 Water damage tends to worsen with time, and it is among the more challenging DIY repairs to undertake, so this guide covers the basic iPhone repair of water damage.  1. Remove iPhone from the water and Turn it off Remove your iPhone from the water as soon as safely possible. Minimize the length of time the iPhone and water are in contact to minimize corrosion. If your phone is still on when removed from the water, attempt to turn it off. If it's off, do not attempt to turn it on. 2. Check External Ports Check any external ports (charging port, headphone jack, SIM card slot, etc.) for corrosion as well. These may have to be cleaned out with alcohol and a  Anti Static Brush , or replaced if cleaning is not practical. Pay special attention to cable ends, battery contacts, connectors, pins, and fuses, as these parts are prone to corrosion and can easily cause the phone to malfunction. Test all the buttons and features (such as the mic...
Read more

2021 Latest MagicAWRT Adapter Restore Tool for Apple Watch

Image
 Here we have the latest MagicAWRT adapter Apple Watch restore tool in 2021, and MagicAWRT offers its complete solutions to fix many apple watch problems. MagicAWRT Adapter is intended for solving service problems with Apple Watch S0/SE/S1/S2/S3/S4/S5/S6 (38 mm / 42 mm / 40 mm / 44 mm). It can solve problems such as white apples, exclamation points, restarts, stuck on screens, poor touch, ID lock, etc. It also can fix related issues that are caused by  Apple Watch glass digitizer touch replacement. Apple Watch Firmware for MagicAWRT Adapter Restore Tool will not be provided, and the customer needs to download themselves. 1. Using MagicAWRT Adapter to reset Apple Watch Data with or without Backup MagicAWRT Recovery Adapter Restore Tool is the best iOS data restore software in the market because of its ease of use and attractive user interface. Most Apple Watch users data losses are due to accidents, failed jailbreaks, hardware and software failures, factory resets, and theft....
Read more

How To Solve iPhone X Voltage Jumping Issue

Image
Today, We getting the iPhone X main board to test, we observe the current value repeatedly jumps between 0mA and 50mA on DC power supply , and it is different from the normal booting current. Next, test whether the power supply of every circuit is normal. PP_VDD_MAIN is measured 4.2V; PP_VDD_BOOST measured is 4.2V. PP1V8-ALWAYS is 1.8V, all the values are normal. But when testing PP1V1_S2, PP0V8_SOC_FIXED_S1, PP1V8_S2 and other circuit voltage that output by power chip U2700 voltage are jumping constantly. According to previous experience, voltage jump is usually caused by a power supply circuit of U2700 output. Measured with digital multimeter , there is no short circuit was found for the dipole value of all power supply to ground. We repaired iPhone 7P before and know that if crystal oscillator is false welding can also cause voltage jumping, And if iPhone CPU power supply is abnormal also can cause voltage jumping. Check the crystal oscillator we find no problem, then check th...
Read more