How To Fix iPhone 6 Plus Common Failure Issue - Everything You Need To know!

Unfortunately, After using your iPhone 6 Plus for a while, you find that it's starting to have a variety of problems. your find the iPhone 6 Plus didn't respond to a sudden touch. It can't be resumed by shutdown, and the touchscreen doesn't work properly. You will be depressed. Don't worry. Today we will teach you how to solve these common problems.



iPhone 6 Plus touch Screen is very easy to get faults: unresponsive, zebra flicker on the top of the screen, etc. Before dealing with these failures, it's necessary to replace a new screen to test, if the failure still exist, you need to test the iPhone 6 Plus motherboard. First test the ground resistance of the touch pin, which can intuitively let us find out where the problem is. 

At the same time, we can see that the 18 pin is the synchronous signal of CPU through the black touch M1 pin. If all these resistances are normal, voltage test should be started. By voltage test, we can more accurately judge which chip is damaged. 

picture11-12-1

The voltage test must be buckled to the screen for voltage output, three power supply for black touch: +-5.7V shows power supply, and 1.8V shows it is given by power IC . As shown in picture 11-12-2.



Two power supply of white touch : 5.1V display power supply, 1.8V power supply IC. As shown in picture 11-12-3. It is possible to judge which IC is damaged according to the results measured. 


The water damaged device shows that the power is easy to burn out so that 5.1V and white touch +-5.7V cannot be given. Broken device fault mostly shows on black touch, false welding is the most possible problem. During the soldering process, some technicians do not remove and redo but directly heat to the chip, customers can use them normally, but they will come back to repair after a while. It is better to take the chips off and replace the new ones.

The point of the black touch M1 pin is at the top of the plate layer, and it is easy to break the wire to cause the iPhone 6 Plus CPU signal to not be delivered, so we need to use the jumper wire to solve this problem. There is a point below the R2410, and the M1 pin is a circuit line, gently scraped with a blade under a magnifying glass, then get a little solder on the blade, blowing a small solder ball out with ESD hot air gun, it must be small, then welding the solder ball at that point scraped out with slow speed air gun, using a copper wire (can take off from solder wick) to fix on the scrape point and M1 pin, add the green oil and put under curing UV light. The process looks more complex, but the effect is very good, and it is basically no rework necessary.


11-12-4

11-12-5

In addition, take care not to damage the small components around the points, here are 2490, FL2486, C2439 three components,which are used for identifying the original screen, after you change the iPhone touch IC and install the original screen, if the screen is still not responsive but assembly screen can work, that is the problem. After installing the black touch IC, check whether the resistance of C1577 is normal, because it goes into IC, and it is surrounded by grounding pins. If the current is directly loaded onto 500mA, most of them are caused from here.


Tips: More information about phone repair guides and tools, you can ask help for Vip Pro Shop Team.

Comments

Post a Comment

Popular posts from this blog

My iPhone Got Wet! How To Fix iPhone Water Damage?

Image
 Water damage tends to worsen with time, and it is among the more challenging DIY repairs to undertake, so this guide covers the basic iPhone repair of water damage.  1. Remove iPhone from the water and Turn it off Remove your iPhone from the water as soon as safely possible. Minimize the length of time the iPhone and water are in contact to minimize corrosion. If your phone is still on when removed from the water, attempt to turn it off. If it's off, do not attempt to turn it on. 2. Check External Ports Check any external ports (charging port, headphone jack, SIM card slot, etc.) for corrosion as well. These may have to be cleaned out with alcohol and a  Anti Static Brush , or replaced if cleaning is not practical. Pay special attention to cable ends, battery contacts, connectors, pins, and fuses, as these parts are prone to corrosion and can easily cause the phone to malfunction. Test all the buttons and features (such as the mic...
Read more

2021 Latest MagicAWRT Adapter Restore Tool for Apple Watch

Image
 Here we have the latest MagicAWRT adapter Apple Watch restore tool in 2021, and MagicAWRT offers its complete solutions to fix many apple watch problems. MagicAWRT Adapter is intended for solving service problems with Apple Watch S0/SE/S1/S2/S3/S4/S5/S6 (38 mm / 42 mm / 40 mm / 44 mm). It can solve problems such as white apples, exclamation points, restarts, stuck on screens, poor touch, ID lock, etc. It also can fix related issues that are caused by  Apple Watch glass digitizer touch replacement. Apple Watch Firmware for MagicAWRT Adapter Restore Tool will not be provided, and the customer needs to download themselves. 1. Using MagicAWRT Adapter to reset Apple Watch Data with or without Backup MagicAWRT Recovery Adapter Restore Tool is the best iOS data restore software in the market because of its ease of use and attractive user interface. Most Apple Watch users data losses are due to accidents, failed jailbreaks, hardware and software failures, factory resets, and theft....
Read more

How To Solve iPhone X Voltage Jumping Issue

Image
Today, We getting the iPhone X main board to test, we observe the current value repeatedly jumps between 0mA and 50mA on DC power supply , and it is different from the normal booting current. Next, test whether the power supply of every circuit is normal. PP_VDD_MAIN is measured 4.2V; PP_VDD_BOOST measured is 4.2V. PP1V8-ALWAYS is 1.8V, all the values are normal. But when testing PP1V1_S2, PP0V8_SOC_FIXED_S1, PP1V8_S2 and other circuit voltage that output by power chip U2700 voltage are jumping constantly. According to previous experience, voltage jump is usually caused by a power supply circuit of U2700 output. Measured with digital multimeter , there is no short circuit was found for the dipole value of all power supply to ground. We repaired iPhone 7P before and know that if crystal oscillator is false welding can also cause voltage jumping, And if iPhone CPU power supply is abnormal also can cause voltage jumping. Check the crystal oscillator we find no problem, then check th...
Read more