Repair iPhone 6s can't add fingerprint failure Problem

The iPhone 6S accidentally dropped into the water, and then it came up with a fingerprint faulty, the iPhone 6S can't add fingerprint. So the customer sent it to us to repair. Now, let's take a closer look at this iPhone and then repair it!



Step 1: First, Disassemble the iPhone by JM-P01 Toolkit, carefully remove the iPhone motherboard. After checking, we found signs of corrosion in the fingerprint socket, and then detect MESA_TO_BOOST_EN_CONN. 

Step 2: Use Fluke 15B+ Digital Multimeter to measure the diode data of PP16V5_MESA_CONN fingerprint boost boot signal and 16.5V, the data is normal. 

Step 3: Observe the iPhone PCB board carefully under the VGA Camera 7-45X Trinocular Stereo Microscope, we found something else. The bottom pin was severely corroded after the corrosion was removed from the fingerprint boost U4040. A2 pin PP_VCC_MAIN is disconnected, and the A1 pin CND close to PP_VCC_MAIN is dropped by corrosion.  Picture 10-16-1



Step 4: Soldering the jump wire on A2 pin via Quick 861DW, but the fault still exists. Why is there such a problem? There are no problems anywhere else, L4040 boost inductance is normal after checking. 

Step 5: We have to rearrange the repair ideas, and then re-check it. Most of the time, we're only one step away from fixing the iPhone, it depends on the details. Open the WUXINJI Dongle to check the iPhone schematic diagram, we found this boost IC bottom pin only has two GND. Picture 10-16-2


Step 6: Someone would say, the ground is interlinked, that's definitely not a problem. The iPhone motherboard GND must be connected. However, after measuring, the two ground of IC bottom pin is disconnected, which means these two are indispensable. If one is missing, it will cause U4040 not to work. After weld the jump wire, the problem of fingerprint that don't have 16.5V has been solved.

Step 7: Install the iPhone and turn on it to test, the fingerprint entry is normal, now you can add fingerprint on your iPhone. Test the other functions, all is fine.

Summary:

Fingerprint bottom pin GND cannot be ignored, because it can cause U4040 IC not working. During the repair process, you can ignore any place that might cause problems. Just be careful and patient.

Tips: If you need more information and professional repair skilled, you want to consult, please check here. We'll give you a free answer. 

Comments

Post a Comment

Popular posts from this blog

My iPhone Got Wet! How To Fix iPhone Water Damage?

Image
 Water damage tends to worsen with time, and it is among the more challenging DIY repairs to undertake, so this guide covers the basic iPhone repair of water damage.  1. Remove iPhone from the water and Turn it off Remove your iPhone from the water as soon as safely possible. Minimize the length of time the iPhone and water are in contact to minimize corrosion. If your phone is still on when removed from the water, attempt to turn it off. If it's off, do not attempt to turn it on. 2. Check External Ports Check any external ports (charging port, headphone jack, SIM card slot, etc.) for corrosion as well. These may have to be cleaned out with alcohol and a  Anti Static Brush , or replaced if cleaning is not practical. Pay special attention to cable ends, battery contacts, connectors, pins, and fuses, as these parts are prone to corrosion and can easily cause the phone to malfunction. Test all the buttons and features (such as the mic...
Read more

2021 Latest MagicAWRT Adapter Restore Tool for Apple Watch

Image
 Here we have the latest MagicAWRT adapter Apple Watch restore tool in 2021, and MagicAWRT offers its complete solutions to fix many apple watch problems. MagicAWRT Adapter is intended for solving service problems with Apple Watch S0/SE/S1/S2/S3/S4/S5/S6 (38 mm / 42 mm / 40 mm / 44 mm). It can solve problems such as white apples, exclamation points, restarts, stuck on screens, poor touch, ID lock, etc. It also can fix related issues that are caused by  Apple Watch glass digitizer touch replacement. Apple Watch Firmware for MagicAWRT Adapter Restore Tool will not be provided, and the customer needs to download themselves. 1. Using MagicAWRT Adapter to reset Apple Watch Data with or without Backup MagicAWRT Recovery Adapter Restore Tool is the best iOS data restore software in the market because of its ease of use and attractive user interface. Most Apple Watch users data losses are due to accidents, failed jailbreaks, hardware and software failures, factory resets, and theft....
Read more

How To Solve iPhone X Voltage Jumping Issue

Image
Today, We getting the iPhone X main board to test, we observe the current value repeatedly jumps between 0mA and 50mA on DC power supply , and it is different from the normal booting current. Next, test whether the power supply of every circuit is normal. PP_VDD_MAIN is measured 4.2V; PP_VDD_BOOST measured is 4.2V. PP1V8-ALWAYS is 1.8V, all the values are normal. But when testing PP1V1_S2, PP0V8_SOC_FIXED_S1, PP1V8_S2 and other circuit voltage that output by power chip U2700 voltage are jumping constantly. According to previous experience, voltage jump is usually caused by a power supply circuit of U2700 output. Measured with digital multimeter , there is no short circuit was found for the dipole value of all power supply to ground. We repaired iPhone 7P before and know that if crystal oscillator is false welding can also cause voltage jumping, And if iPhone CPU power supply is abnormal also can cause voltage jumping. Check the crystal oscillator we find no problem, then check th...
Read more