Repair iPhone 6 no display after boot - Easy Guide

As we all know, The iPhone 6 no display after boot, this is a common fault in iphone6, most users are very angry with this fault, don't worry, Today, The VIP Pro Shop Team will tell you how to Solve this Problem.



First, Measure the diode data of display socket J2019 with Fluke 15B+ Digital Multimeter, there is no exception found in data. Measure the power supply output of iPhone display touch IC, there is no short circuit. When measuring the bootstrap voltage, we found there is no voltage.

We can check the iPhone circuit schematic diagram on WUXINJI Dongle, Picture 12-4-1


When we measure diode data, we found that C1554 had no short circuit, but also no resistance. In normal case, C1554-1 this one end can measure more than 600, the reverse resistance C1554-2 this one end can be measured to more than 600. We initially suspected that the display IC is virtual welding, after replanting the tin with QUICK 861DW Hot Air Rework Station, it doesn't work. Now, our suspicions are disconnected. Remove the display touch IC, and then measure the display touch IC C4# pin and E4# pin to the C1554 these two lines, all is disconnected. Picture 12-4-2.


C1554 on the back, the distance of the welding jump wire is far. In view of aesthetic, so we directly weld the jump wire near the display touch IC C4 # pin and the E4 pin. Picture 12-4-3

After that, install the iPhone 6 and test it, the iPhone touch screen is displayed properly now!

Tips: If you need more information and professional repair skilled, you want to consult, please check here. We'll give you a free answer. 

Comments

Post a Comment

Popular posts from this blog

My iPhone Got Wet! How To Fix iPhone Water Damage?

Image
 Water damage tends to worsen with time, and it is among the more challenging DIY repairs to undertake, so this guide covers the basic iPhone repair of water damage.  1. Remove iPhone from the water and Turn it off Remove your iPhone from the water as soon as safely possible. Minimize the length of time the iPhone and water are in contact to minimize corrosion. If your phone is still on when removed from the water, attempt to turn it off. If it's off, do not attempt to turn it on. 2. Check External Ports Check any external ports (charging port, headphone jack, SIM card slot, etc.) for corrosion as well. These may have to be cleaned out with alcohol and a  Anti Static Brush , or replaced if cleaning is not practical. Pay special attention to cable ends, battery contacts, connectors, pins, and fuses, as these parts are prone to corrosion and can easily cause the phone to malfunction. Test all the buttons and features (such as the mic...
Read more

2021 Latest MagicAWRT Adapter Restore Tool for Apple Watch

Image
 Here we have the latest MagicAWRT adapter Apple Watch restore tool in 2021, and MagicAWRT offers its complete solutions to fix many apple watch problems. MagicAWRT Adapter is intended for solving service problems with Apple Watch S0/SE/S1/S2/S3/S4/S5/S6 (38 mm / 42 mm / 40 mm / 44 mm). It can solve problems such as white apples, exclamation points, restarts, stuck on screens, poor touch, ID lock, etc. It also can fix related issues that are caused by  Apple Watch glass digitizer touch replacement. Apple Watch Firmware for MagicAWRT Adapter Restore Tool will not be provided, and the customer needs to download themselves. 1. Using MagicAWRT Adapter to reset Apple Watch Data with or without Backup MagicAWRT Recovery Adapter Restore Tool is the best iOS data restore software in the market because of its ease of use and attractive user interface. Most Apple Watch users data losses are due to accidents, failed jailbreaks, hardware and software failures, factory resets, and theft....
Read more

How To Solve iPhone X Voltage Jumping Issue

Image
Today, We getting the iPhone X main board to test, we observe the current value repeatedly jumps between 0mA and 50mA on DC power supply , and it is different from the normal booting current. Next, test whether the power supply of every circuit is normal. PP_VDD_MAIN is measured 4.2V; PP_VDD_BOOST measured is 4.2V. PP1V8-ALWAYS is 1.8V, all the values are normal. But when testing PP1V1_S2, PP0V8_SOC_FIXED_S1, PP1V8_S2 and other circuit voltage that output by power chip U2700 voltage are jumping constantly. According to previous experience, voltage jump is usually caused by a power supply circuit of U2700 output. Measured with digital multimeter , there is no short circuit was found for the dipole value of all power supply to ground. We repaired iPhone 7P before and know that if crystal oscillator is false welding can also cause voltage jumping, And if iPhone CPU power supply is abnormal also can cause voltage jumping. Check the crystal oscillator we find no problem, then check th...
Read more