How to Repair iPhone 6 overheating and won't boot Issue

The customer says the iPhone 6 battery has been replaced, it can go into IOS before, but not now; Sometimes have the WIFI and Bluetooth, but sometimes haven’t; the iPhone battery consumption is fast, and iPhone is overheating.



Comprehensive information provided by customer, we think this is caused by the damage to the iPhone WiFi chip. The iPhone can be powered on before, but not boot now, mostly because the batteries are running out.

Using JM-9102 Disassemble Tools to dismantle the iPhone, test the battery, it's really running out of power. Just leave it alone first，and supply power on the iPhone motherboard. Picture 12-2-1


As shown above picture, it's leaking 200mA. Now measure the diode data of VCC_MAIN with Fluke 15B+ Digital Multimeter, as shown in the following picture, Picture 12-2-2


Judging from the test results, the diode data of VCC_MAIN is low. Think of the customer before said WiFi sometimes good sometimes bad, so we directly remove the iPhone WIFI IC. Picture 12-2-3


After removing the WIFI chip, measure it again, now the diode data of VCC_MAIN is back to normal. Using DC power supply to provide the power to iPhone motherboard to test. Picture 12-2-4


The iPhone standby current is normal, no more leakage. Find new WiFi chip and install it, the boot current also normal. Directly assemble the iPhone, the charging current has 1A, which means the previous judgment is correct. After booting, the WIFI and Bluetooth are available.


Tips: If you need more information and professional repair skilled, you want to consult, please check here. We'll give you a free answer. 


Comments

Post a Comment

Popular posts from this blog

My iPhone Got Wet! How To Fix iPhone Water Damage?

Image
 Water damage tends to worsen with time, and it is among the more challenging DIY repairs to undertake, so this guide covers the basic iPhone repair of water damage.  1. Remove iPhone from the water and Turn it off Remove your iPhone from the water as soon as safely possible. Minimize the length of time the iPhone and water are in contact to minimize corrosion. If your phone is still on when removed from the water, attempt to turn it off. If it's off, do not attempt to turn it on. 2. Check External Ports Check any external ports (charging port, headphone jack, SIM card slot, etc.) for corrosion as well. These may have to be cleaned out with alcohol and a  Anti Static Brush , or replaced if cleaning is not practical. Pay special attention to cable ends, battery contacts, connectors, pins, and fuses, as these parts are prone to corrosion and can easily cause the phone to malfunction. Test all the buttons and features (such as the mic...
Read more

2021 Latest MagicAWRT Adapter Restore Tool for Apple Watch

Image
 Here we have the latest MagicAWRT adapter Apple Watch restore tool in 2021, and MagicAWRT offers its complete solutions to fix many apple watch problems. MagicAWRT Adapter is intended for solving service problems with Apple Watch S0/SE/S1/S2/S3/S4/S5/S6 (38 mm / 42 mm / 40 mm / 44 mm). It can solve problems such as white apples, exclamation points, restarts, stuck on screens, poor touch, ID lock, etc. It also can fix related issues that are caused by  Apple Watch glass digitizer touch replacement. Apple Watch Firmware for MagicAWRT Adapter Restore Tool will not be provided, and the customer needs to download themselves. 1. Using MagicAWRT Adapter to reset Apple Watch Data with or without Backup MagicAWRT Recovery Adapter Restore Tool is the best iOS data restore software in the market because of its ease of use and attractive user interface. Most Apple Watch users data losses are due to accidents, failed jailbreaks, hardware and software failures, factory resets, and theft....
Read more

How To Solve iPhone X Voltage Jumping Issue

Image
Today, We getting the iPhone X main board to test, we observe the current value repeatedly jumps between 0mA and 50mA on DC power supply , and it is different from the normal booting current. Next, test whether the power supply of every circuit is normal. PP_VDD_MAIN is measured 4.2V; PP_VDD_BOOST measured is 4.2V. PP1V8-ALWAYS is 1.8V, all the values are normal. But when testing PP1V1_S2, PP0V8_SOC_FIXED_S1, PP1V8_S2 and other circuit voltage that output by power chip U2700 voltage are jumping constantly. According to previous experience, voltage jump is usually caused by a power supply circuit of U2700 output. Measured with digital multimeter , there is no short circuit was found for the dipole value of all power supply to ground. We repaired iPhone 7P before and know that if crystal oscillator is false welding can also cause voltage jumping, And if iPhone CPU power supply is abnormal also can cause voltage jumping. Check the crystal oscillator we find no problem, then check th...
Read more