Solution For iPhone 6 Plus Weak Wifi Signal Repair

Many people are going to have this problem，The iPhone 6 Plus got weak Wi-Fi in house and cannot reconnect. When toggling Wi-Fi off and back on it doesn't even pick any network in range, How to fix weak Wi-Fi signal on iPhone 6 Plus? Now, VIP Pro Shop Team will provide us with practical solutions.

The WIFI of iPhone 6 Plus can be turned on, but its signal is weak. If you stay away from the router, WiFi is completely out of signal. After we test it, it only can search 2 wifi addresses, and the signal is weak. However, there are ten or more wifi address can be found on the phone with no fault. So, we can judge the fault is weak WIFI signal.



Step 1. Disassemble iPhone with phone opening tools and take out the motherboard, we can found that the iPhone WIFI chip has been replaced. In order to test whether the chip is workable, we solder the jump wire first to replace the peripheral antenna circuit of the wifi chip. The method of welding jump wire is that using a 10 cm enameled wire acting as antenna starting from C5213_RF near WiFi.



Step 2. Power on iPhone to test when finish the soldering jump wire with soldering station, many WiFi hotspots can be found now, and at the same time, the signal has been normal. Why the wifi signal back to normal after we weld jump wire? This is mainly because the WiFi signal filter FL_CELL_WIF_RF has been damaged, and the removal of filter has no effect on the iPhone operation. In the case of repair, we often solder the jump wire directly ignoring the filter.

Step 3. Apply some green UV oil on the jump wire and fix it, then assemble the iPhone. Power on iPhone and test it, now the WIFI signal is normal, the iPhone 6 Plus has been repaired.


Tips: If you need more information and professional repair skilled, you want to consult, please check here. We'll give you a free answer. 

Comments

Post a Comment

Popular posts from this blog

My iPhone Got Wet! How To Fix iPhone Water Damage?

Image
 Water damage tends to worsen with time, and it is among the more challenging DIY repairs to undertake, so this guide covers the basic iPhone repair of water damage.  1. Remove iPhone from the water and Turn it off Remove your iPhone from the water as soon as safely possible. Minimize the length of time the iPhone and water are in contact to minimize corrosion. If your phone is still on when removed from the water, attempt to turn it off. If it's off, do not attempt to turn it on. 2. Check External Ports Check any external ports (charging port, headphone jack, SIM card slot, etc.) for corrosion as well. These may have to be cleaned out with alcohol and a  Anti Static Brush , or replaced if cleaning is not practical. Pay special attention to cable ends, battery contacts, connectors, pins, and fuses, as these parts are prone to corrosion and can easily cause the phone to malfunction. Test all the buttons and features (such as the mic...
Read more

2021 Latest MagicAWRT Adapter Restore Tool for Apple Watch

Image
 Here we have the latest MagicAWRT adapter Apple Watch restore tool in 2021, and MagicAWRT offers its complete solutions to fix many apple watch problems. MagicAWRT Adapter is intended for solving service problems with Apple Watch S0/SE/S1/S2/S3/S4/S5/S6 (38 mm / 42 mm / 40 mm / 44 mm). It can solve problems such as white apples, exclamation points, restarts, stuck on screens, poor touch, ID lock, etc. It also can fix related issues that are caused by  Apple Watch glass digitizer touch replacement. Apple Watch Firmware for MagicAWRT Adapter Restore Tool will not be provided, and the customer needs to download themselves. 1. Using MagicAWRT Adapter to reset Apple Watch Data with or without Backup MagicAWRT Recovery Adapter Restore Tool is the best iOS data restore software in the market because of its ease of use and attractive user interface. Most Apple Watch users data losses are due to accidents, failed jailbreaks, hardware and software failures, factory resets, and theft....
Read more

How To Solve iPhone X Voltage Jumping Issue

Image
Today, We getting the iPhone X main board to test, we observe the current value repeatedly jumps between 0mA and 50mA on DC power supply , and it is different from the normal booting current. Next, test whether the power supply of every circuit is normal. PP_VDD_MAIN is measured 4.2V; PP_VDD_BOOST measured is 4.2V. PP1V8-ALWAYS is 1.8V, all the values are normal. But when testing PP1V1_S2, PP0V8_SOC_FIXED_S1, PP1V8_S2 and other circuit voltage that output by power chip U2700 voltage are jumping constantly. According to previous experience, voltage jump is usually caused by a power supply circuit of U2700 output. Measured with digital multimeter , there is no short circuit was found for the dipole value of all power supply to ground. We repaired iPhone 7P before and know that if crystal oscillator is false welding can also cause voltage jumping, And if iPhone CPU power supply is abnormal also can cause voltage jumping. Check the crystal oscillator we find no problem, then check th...
Read more