Solution Here! Why iPhone6 Plus Front Camera Doesn't Work

If you see a black screen or your iPhone front camera Not Working, What Should you do, we've summed up some practical ways, follow the article steps below to fix the problem. 

All the functions of the iPhone6 Plus are normal, it can be switched normally between front and rear camera, however, the iPhone front camera is shown full black screen when taking photos. As shown in pictue 9-10-1.



Step 1: First, we need to judge where the problem comes from. This failure is generally caused by data hub, because the problem came up after falling, so it is likely to be caused by the disconnection or iPhone CPU false welding.

Step 2: Disassemble and install a new camera, same fault phenomenon remains the same, the problem is determined on the iPhone6 Plus motherboard.

Step 3: Power off the phone and measure the ground value of the camera interface, there is no any problems has been found, also the voltage needed for the camera is measured normally. This is a rare situation. If the CPU is false welding, the resistance shouldn't be normal, so there is almost impossible for getting a bad CPU.

Step 4:  Test the interface resistance again, infinity is detected when the 19th pin AP_BI_FCAM_SDA_FONN is measured. As shown in picture 9-10-2.



Step 5:  Many tests found that sometimes it's infinite, sometimes more than 500 of the resistance, but according to the data cable comparison found that under normal circumstances, it should not exceed 500. Measured valure on multimeter is as shown in picture 9-10-3.



Step 6:  Tracing the source, it was found that the AP_NO_FCA_SDA_CONN was connected to the CPU by inductance, and the resistance of the 1 pin measured by FL1114 was normal. As shown in picture 9-10-4.



Step 7:  After measuring FL1114's 2 pin infinity, we find that some inductance is loose, after sodering, 19 pin resistance become normal. Booting and entering into the system to test, the front camera has been fixed already!


Tips: If you need more information and professional repair skilled, you want to consult, please check  VIP Pro Shop Team. We'll give you a free answer. 

Comments

Post a Comment

Popular posts from this blog

My iPhone Got Wet! How To Fix iPhone Water Damage?

Image
 Water damage tends to worsen with time, and it is among the more challenging DIY repairs to undertake, so this guide covers the basic iPhone repair of water damage.  1. Remove iPhone from the water and Turn it off Remove your iPhone from the water as soon as safely possible. Minimize the length of time the iPhone and water are in contact to minimize corrosion. If your phone is still on when removed from the water, attempt to turn it off. If it's off, do not attempt to turn it on. 2. Check External Ports Check any external ports (charging port, headphone jack, SIM card slot, etc.) for corrosion as well. These may have to be cleaned out with alcohol and a  Anti Static Brush , or replaced if cleaning is not practical. Pay special attention to cable ends, battery contacts, connectors, pins, and fuses, as these parts are prone to corrosion and can easily cause the phone to malfunction. Test all the buttons and features (such as the mic...
Read more

2021 Latest MagicAWRT Adapter Restore Tool for Apple Watch

Image
 Here we have the latest MagicAWRT adapter Apple Watch restore tool in 2021, and MagicAWRT offers its complete solutions to fix many apple watch problems. MagicAWRT Adapter is intended for solving service problems with Apple Watch S0/SE/S1/S2/S3/S4/S5/S6 (38 mm / 42 mm / 40 mm / 44 mm). It can solve problems such as white apples, exclamation points, restarts, stuck on screens, poor touch, ID lock, etc. It also can fix related issues that are caused by  Apple Watch glass digitizer touch replacement. Apple Watch Firmware for MagicAWRT Adapter Restore Tool will not be provided, and the customer needs to download themselves. 1. Using MagicAWRT Adapter to reset Apple Watch Data with or without Backup MagicAWRT Recovery Adapter Restore Tool is the best iOS data restore software in the market because of its ease of use and attractive user interface. Most Apple Watch users data losses are due to accidents, failed jailbreaks, hardware and software failures, factory resets, and theft....
Read more

How To Solve iPhone X Voltage Jumping Issue

Image
Today, We getting the iPhone X main board to test, we observe the current value repeatedly jumps between 0mA and 50mA on DC power supply , and it is different from the normal booting current. Next, test whether the power supply of every circuit is normal. PP_VDD_MAIN is measured 4.2V; PP_VDD_BOOST measured is 4.2V. PP1V8-ALWAYS is 1.8V, all the values are normal. But when testing PP1V1_S2, PP0V8_SOC_FIXED_S1, PP1V8_S2 and other circuit voltage that output by power chip U2700 voltage are jumping constantly. According to previous experience, voltage jump is usually caused by a power supply circuit of U2700 output. Measured with digital multimeter , there is no short circuit was found for the dipole value of all power supply to ground. We repaired iPhone 7P before and know that if crystal oscillator is false welding can also cause voltage jumping, And if iPhone CPU power supply is abnormal also can cause voltage jumping. Check the crystal oscillator we find no problem, then check th...
Read more