Solve Cannot Boot Problems in iPhone 6 - step by step

We Received an iPhone 6 from one of our customers, the problem is told that it can not boot, the iPhone device shows large short circuit when connecting with adjustable power supply. Disassemble the device we find that the flash position is hot, so we tear it down and find the solder pad is burned a hole. As shown in picture 9-6-1.


PP_VCC_MAIN is short circuit, but it turns normally after removing L1605 inductance, however, the other end of L1605 to U1602 flash chip is still short circuit, so we directly dig from the burning hole till it's not short. 

There are 2 useful wire below the hole after we dig it: one is from U1602 flash chip E3 pin RCAM_TO_LEDDRV_STROBE_EN  to rear camera 30 pin; the other is from CPU to transposon interrupt signal ALS_TO_AP_INT_L  of J1111. As shown in picture 9-6-2



Solder the 2 wire with jumper wires, and apply the green oil to solidify it. As shown in picture  9-6-3 and 9-6-4.




Then we repair the iPhone solder pad and fill the flash chip, as shown in picture 9-6-5 and 9-6-6.




Now, we boot the iPhone 6 to have a test, as shown in picture 9-6-7. All the function are normal now, repair ends here!



Tips: More about iPhone 6 Cannot Boot information and iphone repair skills, you can view and free consulting VIP Pro Shop Team. Or leave a message.

Comments

Post a Comment

Popular posts from this blog

My iPhone Got Wet! How To Fix iPhone Water Damage?

Image
 Water damage tends to worsen with time, and it is among the more challenging DIY repairs to undertake, so this guide covers the basic iPhone repair of water damage.  1. Remove iPhone from the water and Turn it off Remove your iPhone from the water as soon as safely possible. Minimize the length of time the iPhone and water are in contact to minimize corrosion. If your phone is still on when removed from the water, attempt to turn it off. If it's off, do not attempt to turn it on. 2. Check External Ports Check any external ports (charging port, headphone jack, SIM card slot, etc.) for corrosion as well. These may have to be cleaned out with alcohol and a  Anti Static Brush , or replaced if cleaning is not practical. Pay special attention to cable ends, battery contacts, connectors, pins, and fuses, as these parts are prone to corrosion and can easily cause the phone to malfunction. Test all the buttons and features (such as the mic...
Read more

2021 Latest MagicAWRT Adapter Restore Tool for Apple Watch

Image
 Here we have the latest MagicAWRT adapter Apple Watch restore tool in 2021, and MagicAWRT offers its complete solutions to fix many apple watch problems. MagicAWRT Adapter is intended for solving service problems with Apple Watch S0/SE/S1/S2/S3/S4/S5/S6 (38 mm / 42 mm / 40 mm / 44 mm). It can solve problems such as white apples, exclamation points, restarts, stuck on screens, poor touch, ID lock, etc. It also can fix related issues that are caused by  Apple Watch glass digitizer touch replacement. Apple Watch Firmware for MagicAWRT Adapter Restore Tool will not be provided, and the customer needs to download themselves. 1. Using MagicAWRT Adapter to reset Apple Watch Data with or without Backup MagicAWRT Recovery Adapter Restore Tool is the best iOS data restore software in the market because of its ease of use and attractive user interface. Most Apple Watch users data losses are due to accidents, failed jailbreaks, hardware and software failures, factory resets, and theft....
Read more

How To Solve iPhone X Voltage Jumping Issue

Image
Today, We getting the iPhone X main board to test, we observe the current value repeatedly jumps between 0mA and 50mA on DC power supply , and it is different from the normal booting current. Next, test whether the power supply of every circuit is normal. PP_VDD_MAIN is measured 4.2V; PP_VDD_BOOST measured is 4.2V. PP1V8-ALWAYS is 1.8V, all the values are normal. But when testing PP1V1_S2, PP0V8_SOC_FIXED_S1, PP1V8_S2 and other circuit voltage that output by power chip U2700 voltage are jumping constantly. According to previous experience, voltage jump is usually caused by a power supply circuit of U2700 output. Measured with digital multimeter , there is no short circuit was found for the dipole value of all power supply to ground. We repaired iPhone 7P before and know that if crystal oscillator is false welding can also cause voltage jumping, And if iPhone CPU power supply is abnormal also can cause voltage jumping. Check the crystal oscillator we find no problem, then check th...
Read more